Exclusion of a Qubino Flush device from a Z-Wave network


Exclusion of the Qubino Smart Meter or Qubino 3 Phase Smart Meter from a Z-Wave network


Exclusion of the Qubino DIN Dimmer from a Z-Wave network

Exclusion of the Qubino Flush RGBW Dimmer from a Z-Wave network

Exclusion of the Qubino Smart Plug from a Z-Wave network

Exclusion of the Luxy Smart Switch from a Z-Wave network


Removal of a Qubino Flush device from a Z-Wave network (Z-Wave exclusion)

  • Connect the device to the power supply if not already connected
  • Make sure the device is within direct range of your Z-Wave gateway (hub) or use a handheld Z-Wave remote to perform exclusion
  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Toggle the switch connected to the I1 terminal 3 times within 5 seconds (The device has to get On/Off signal 3 times, meaning 3 times push of the push button or with the normal button On / Off / On / Off / On / Off)
    OR
    If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 3 and 5 seconds
  • The device will be removed from your network but any custom configuration parameters will not be erased


Removal of the Qubino Smart Meter or 3 Phase Smart Meter from a Z-Wave network (Z-Wave exclusion)

  • Connect the device to the power supply if not already connected
  • Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion 
  • Enable add/remove mode on your Z-Wave gateway (hub) 
  • Press and hold the S service button between 0.2 and 3 seconds 
  • Exclusion with the S service button is not limited by time 
  • The device will be removed from your network but custom configuration parameters will not be erased. Wait at least 30 seconds before adding the device back to a network. 

Removal of the Qubino DIN Dimmer from a Z-Wave network (Z-Wave exclusion)

  • Connect the device to the power supply if not already connected
  • Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion
  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Toggle the switch connected to the I1 terminal 3 times within 3 seconds

    OR
  • Press and hold the S (Service) button between 2 and 6 seconds
  • The device will be removed from your network but any custom configuration parameters will
    not be erased

     

Removal of the Qubino Flush RGBW Dimmer from a Z-Wave network (Z-Wave exclusion)

  • Connect the device to the power supply if not already connected 
  • Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion 
  • Enable add/remove mode on your Z-Wave gateway (hub) 
  • Press and release the S button 3 times within 2 seconds 
  • After exclusion device will automatically attempt to re-include in the next 2 minutes. 
  • The device will be removed from your network but any custom configuration parameters will not be erased 

Removal of the Qubino Smart Plug from a Z-Wave network (Z-Wave exclusion)

  • Connect the device to the power supply if not already connected
  • Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion
  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Press and hold the Service button S from 2 to 6 seconds (with holding the S button for the interval between 2 and 6 seconds you put the device in EXCLUSION MODE)
  • Exclusion with the S service button is not limited by time The device will be removed from your network, but any custom configuration parameters will not be erased

Removal of a Luxy Smart Switch device from a Z-Wave network (Z-Wave exclusion)


Nr. 1 (CENTER)Turns ON/OFF the room light or other load connected to Luxy Smart Switch output
Nr. 2 (UP)Turns ON/OFF the Luxy light Dims the Luxy light
Nr. 3 (RIGHT)Switches between 4 different lighting effects (ocean, sunrise, rainbow, and nature)
Nr. 4 (DOWN)Turns ON/OFF the white light on the Luxy Dims the Luxy light
Nr. 5 (LEFT)Starts the colour spectrum and stops at the colour you wish to have


  • Connect the device to the power supply if not already connected
  • Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion
  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Press once on button 3 – right. One press on button 4 – down for enabling full white. When full white is enabled, press, and hold button 3 – right for 5 seconds. After 5 seconds, the device starts flashing red 1 second ON, 0.5 second OFF. Once the device loses node ID (after 10 seconds), it stops flashing and turns full red. The procedure is always available.