Removing the device from a Z-Wave network (Exclusion) : Qubino Help Center

Connect the device to the power supply if not already connected
Make sure the device is within direct range of your Z-Wave gateway (hub) or use a handheld Z-Wave remote to perform exclusion
Enable add/remove mode on your Z-Wave gateway (hub)
Toggle the switch connected to the I1 terminal 3 times within 3 seconds (The device has to get On/Off signal 3 times, meaning 3 times push of the push button or with the normal button On / Off / On / Off / On / Off)
OR
If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 3 and 5 seconds
The device will be removed from your network but any custom configuration parameters will not be erased

Connect the device to the power supply if not already connected
Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion
Enable add/remove mode on your Z-Wave gateway (hub)
Press and hold the S service button between 0.2 and 3 seconds
Exclusion with the S service button is not limited by time
The device will be removed from your network but custom configuration parameters will not be erased. Wait at least 30 seconds before adding the device back to a network.

Connect the device to the power supply if not already connected
Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion
Enable add/remove mode on your Z-Wave gateway (hub)
Toggle the switch connected to the I1 terminal 3 times within 3 seconds

OR
Press and hold the S (Service) button between 2 and 6 seconds
The device will be removed from your network but any custom configuration parameters will
not be erased

Connect the device to the power supply if not already connected
Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion
Enable add/remove mode on your Z-Wave gateway (hub)
Press and release the S button 3 times within 2 seconds
After exclusion device will automatically attempt to re-include in the next 2 minutes.
The device will be removed from your network but any custom configuration parameters will not be erased

Connect the device to the power supply if not already connected
Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion
Enable add/remove mode on your Z-Wave gateway (hub)
Press and hold the Service button S from 2 to 6 seconds (with holding the S button for the interval between 2 and 6 seconds you put the device in EXCLUSION MODE)
Exclusion with the S service button is not limited by time The device will be removed from your network, but any custom configuration parameters will not be erased

Nr. 1 (CENTER)	Turns ON/OFF the room light or other load connected to Luxy Smart Switch output
Nr. 2 (UP)	Turns ON/OFF the Luxy light Dims the Luxy light
Nr. 3 (RIGHT)	Switches between 4 different lighting effects (ocean, sunrise, rainbow, and nature)
Nr. 4 (DOWN)	Turns ON/OFF the white light on the Luxy Dims the Luxy light
Nr. 5 (LEFT)	Starts the colour spectrum and stops at the colour you wish to have

Connect the device to the power supply if not already connected
Make sure the device is within direct range of your Z-Wave gateway (hub) or use a hand-held Z-Wave remote to perform exclusion
Enable add/remove mode on your Z-Wave gateway (hub)
Press once on button 3 – right. One press on button 4 – down for enabling full white. When full white is enabled, press, and hold button 3 – right for 5 seconds. After 5 seconds, the device starts flashing red 1 second ON, 0.5 second OFF. Once the device loses node ID (after 10 seconds), it stops flashing and turns full red. The procedure is always available.

Removing the device from a Z-Wave network (Exclusion)