Qubino Flush Devices
Automatically adding the device to a Z-Wave network (auto inclusion)

  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Connect the device to the power supply (in case of use with the temperature sensor already connected –sold separately*).
  • Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the device will automatically enrol in your network


Note: For the devices with the S2 secure inclusion please check the Z-Wave Security


Manually adding the device to a Z-Wave network (manual inclusion)

  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Connect the device to the power supply (in case of use with the temperature sensor already connected*)
  • Toggle the switch connected to the I1 terminal 3 times within 5 seconds (The device has to get On/Off signal 3 times, meaning 3 times push of the push button or with the normal button On / Off / On / Off / On / Off)

    OR 

    If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 3 and 5 seconds 

    Note: This proces can be repeated multiple times in a row during the time that the inclusion is running on the gateway. Example: while the Gateway is the inclusion mode toggle the switch 3 times within 3 seconds wait at least 5 seconds and retry to toggle the switch 3 times within 3 seconds, wait at least 5 seconds retry...


  • A new device will appear on your dashboard


*Info: If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor.



Qubino Smart Meter and Qubino 3 Phase Smart Meter 

Automatically adding the Smart Meter to a Z-Wave network (auto inclusion)

  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Automatic selection of secure/unsecure inclusion
  • The device can be automatically added to a Z-Wave network during the first 2 minutes
  • Connect the device to the power supply
  • Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the device will be automatically added to your network (when the device is excluded and re-connected to the power supply it automatically enters the LEARN MODE state.)


Note: For S2 inclusion please check the Z-Wave Security


Manually adding the Smart Meter to a Z-Wave network (manual inclusion)

  • Connect the device to the power supply
  • Enable add/remove mode on your Z-Wave gateway (hub) 
  • Toggle the S service button S between 0.2 and 3 seconds 
  • A new multi-channel device will appear on your dashboard 
  • Inclusion with the S service button is not limited by time 

Qubino DIN Dimmer
Automatically adding the DIN Dimmer to a Z-Wave network (auto inclusion)

  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Connect the device to the power supply (in case of use, with the temperature sensor already connected – sold separately*)
  • Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the
    device will automatically enrol in your network.
  • If the device is properly included, the green LED will stay ON
     

Manually adding the DIN Dimmer to a Z-Wave network (manual inclusion)

  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Connect the device to the power supply (in case of use with the temperature sensor already connected*)
  • Toggle the switch connected to the I1 terminal 3 times within 5 seconds (The device has to get On/Off signal 3 times, meaning 3 times push of the push button or with the normal button On / Off / On / Off / On / Off)

    OR 

    Press and hold the S (Service) button between 3 and 5 seconds 

    Note: This proces can be repeated multiple times in a row during the time that the inclusion is running on the gateway. Example: while the Gateway is the inclusion mode toggle the switch 3 times within 3 seconds wait at least 5 seconds and retry to toggle the switch 3 times within 3 seconds, wait at least 5 seconds retry...


  • A new device will appear on your dashboard


*Info: If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor.

Qubino Flush RGBW Dimmer 

Automatically adding the RGBW Dimmer to a Z-Wave network (auto inclusion)

  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Connect the device to the power supply
  • Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the
    device will automatically enrol in your network.
  • If the device is properly included, the green LED inside the device will stay ON
     

Manually adding the RGBW Dimmer to a Z-Wave network (manual inclusion)

  • Connect the device to the power supply 
  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Press and release the S button 3 times within 2 seconds
  • If the device is properly included, the green LED inside the device will stay ON
     

Qubino Smart Plug

Automatically adding the Smart Plug to a Z-Wave network (auto inclusion)

  • Enable add/remove mode on your Z-Wave gateway (hub) 
  • Automatic selection of secure/unsecure inclusion 
  • The device can be automatically added to a Z-Wave network during the first 2 minutes 
  • Connect the device to the power supply 
  • Auto-inclusion will be initiated within 5 seconds of connection to the power supply and the device will automatically enrol in your network (when the device is excluded and connected to the power supply it automatically enters the INCLUSION MODE state.) 


Note: For S2 inclusion please check the Z-Wave Security


Manually adding the Smart Plug to a Z-Wave network (manual inclusion)

  • Connect the device to the power supply 
  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Press and hold the Service button S from 2 to 6 seconds (with holding the S button for the interval between 2 and 6 seconds you put the device in INCLUSION MODE) 
  • A new device will appear on your dashboard 
  • Inclusion with the S service button is not limited by time 


Luxy Smart Switch
Automatically adding the Luxy Smart Switch to a Z-Wave network (auto inclusion)

  • Scan QR code on device label and add S2 DSK to Provisioning List in gateway (hub)
  • Connect the device to the power supply
  • Make sure the device is within direct range of your Z-Wave gateway (hub)
  • Inclusion will be initiated automatically within few seconds of connection to the power supply and the device will automatically enrol in your network (when the device is excluded and connected to the power supply it automatically enters the LEARN MODE state). 


Note: For S2 inclusion please check the Z-Wave Security


Manually adding the Luxy Smart Switch to a Z-Wave network (manual inclusion)

Nr. 1 (CENTER)
Turns ON/OFF the room light or other load connected to Luxy Smart Switch output
Nr. 2 (UP)
Turns ON/OFF the Luxy light Dims the Luxy light
Nr. 3 (RIGHT)
Switches between 4 different lighting effects (ocean, sunrise, rainbow, and nature)
Nr. 4 (DOWN)
Turns ON/OFF the white light on the Luxy Dims the Luxy light
Nr. 5 (LEFT)
Starts the colour spectrum and stops at the colour you wish to have


  • Enable add/remove mode on your Z-Wave gateway (hub)
  • Connect the device to the power supply
  • Make sure the device is within direct range of your Z-Wave gateway (hub)
  • Press once on button 3 – right. One press on button 4 – down for enabling full white. When full white is enabled, press, and hold button 3 – right, between 4 and 6 seconds. After 6 seconds, the device starts flashing green (1 second ON, 0.5 second OFF). Once the device receives node ID (after 10 seconds), it stops flashing and turns full green. The procedure is always available. 


Z-Wave Security 


Some Qubino devices supports the latest Security 2 feature. Security S2 is handled by the Strong AES 128 Encryption protocol, which means that the S2 makes Z-Wave the most secure IoT (Internet of Things) security platform out there. In order to fully utilize the product and its SECURITY 2 feature, a Security Enabled Z-Wave gateway (hub) must be used. 


Authenticated Control

  • Out-Of-Band Device Specific Key for inclusion
  • May be used by most implementations 


Also supports: Security S2 Unauthenticated, Security S0 and Unsecure inclusion. 


IMPORTANT: When adding a S2 enabled Qubino device to a Z-Wave network with a controller supporting Security 2 (S2), the Z-Wave Device Specific Key (DSK) is required. The unique DSK code is printed on the side label of the product and a copy is inserted in the packaging, which must not be lost. Do not remove the DSK from the product. As a backup measure, please use the label in the packaging to record the location where the product has been installed. 


The first five digits of key is highlighted or underlined to help the user identify the PIN code portion of the DSK text. 


The DSK is additionally represented with a QR Code as shown here. 


DSK label and QR code (example) 


A joining node requesting to join the S2 Access Control Class or the S2 Authenticated Class will obfuscate its Public Key by setting the bytes 1...2 to zeros (0x00) before transferring its key via RF. 


A joining node requesting to join only the S2 Unauthenticated Class will send the its full Public Key when transferring the key via RF as the including node has no access to the DSK. 


The DSK may be used for out-of-band (OOB) authentication in two ways. 

  • The including gateway (hub) may use QR code scanning to read the entire DSK off the joining device and match it with the obfuscated public key received via RF from the joining device. EN. 60 
  • Else the including gateway (hub) will ask the user to enter a 5 digits PIN code (the 5 first digits of the DSK label) in order to substitute the obfuscated bytes of the joining node’s Public Key. The including gateway (hub) may additionally ask the user to visually validate that the rest of the DSK with the Public Key received via RF.